Table of Contents
- 1Build a playhouse by Les Kenny
- 2Identifying the members
- 3Lumber and materials information
- 4Shopping and Cutting lists
- 5Plans - Footprint and front elevation
- 6Plans - Rear and Side Elevation
- 7Plans - Roof, cuts and angles
- 8Making a wood floor
- 9Making a concrete floor
- 10Making the playhouse wall frames
- 11Making the playhouse roof frame
- 12Putting on the playhouse roof cover
- 13Putting on the playhouse wall cover
- 14Making the door
- 15Making the playhouse door frame
- 16Installing the playhouse door
- 17How to make a playhouse window
- 18Making the window sash
- 19Installing the playhouse window
- 20Playhouse Gable and Soffit
- 21Inside finishing
Shopping and Cutting lists
Shopping list
Scroll down for cutting list.
Note 1: The list does not include door or window materials or make allowances for nails, hinges, door latches, door bolts, window catches, caulking sealant or any fasteners.
Note 2: Door and window materials will be dealt with on the respective door and window pages.
Lumber / Material | Used For | Amount |
---|---|---|
100×50 (2×4) Dressed framing lumber | Walls and roof | 100 lineal meters (330 lienal ft) |
300×25 (1×12) suitable for exterior use | Soffit board under eaves and under gable overhang | 3.8 lineal meters (13 lienal ft) |
150×25 (1×6) suitable for exterior use | Fascia board and Barge board (gable rake board) | 10.5 lineal meters (25 lineal ft) |
100×25 (1×4) suitable for exterior use | Barge board capping | 5.5 lineal meters (18 lienal ft) |
50×25 (1×2) suitable for exterior use | Gable battens | 8 lineal meters (26 lienal ft) |
50×25 (1×2) | Inside finishing trim | 14 lienal meters (45 lienal ft) |
25×25 (1×1) | Trim around window (interior) | 5.5 lienal meters (18 lienal ft) |
1200mm x 2400mm(4’x8′) plywood sheets 9mm (3/8”) thick | Roof sheathing | 2 sheets |
1200mm x 2400mm (4’x8′) plywood sheets 12mm (1/2”) thick | Gable ends cover (siding) | 1 sheets |
50×50 (2×2) galvanized flashing | Ridge capping | 2400mm (8ft) |
Cement fibreboard siding or alternative type weather board | Roof cover / Siding / gable soffit board | Enough to cover 15.2 sq meters (164 sq ft) |
Building wrap, cover underlay or similar | Under siding and roof boards | 16 sq meters (172 sq ft) |
FLOOR: Option one – Lumber floor | ||
100×100 (4×4) Treated lumber | Skids | 2 pieces at 1800mm (72”) |
100×50 (2×4) Treated lumber | Floor Joists and rim joists | 15 lineal meters (50 lineal ft) |
1200m x 2400mm (4’x8′) plywood sheets 18mm (3/4”) thick | Floor | 1.5 sheets |
FLOOR: Option two – Concrete slab | ||
40kg (94lb) bags of Portland cement | Concrete slab | 3 bags |
Sand | Concrete slab | Approximately 0.2 cubic meters (7 cubic ft) |
Gravel 20mm (3/4”) diameter and smaller | Concrete slab | Approximately 0.3 cubic meters (11 cubic ft) |
#3 rebar (10mm (3/8”) steel rod) | Concrete slab | 10 meters (30 ft) |
EXTERIOR CORNERS: Option one – soakers | ||
Galvanized soakers | Exterior corners | 24 |
EXTERIOR CORNERS: Option two – wood trim | ||
100×25 (1×4) suitable for exterior use | Exterior corners | Four pieces @ 1300mm 52” |
75×25 (1×3) suitable for exterior use | Exterior corners | Four pieces @ 1300mm 52” |
Frame cutting list
Amount and length | Used for |
---|---|
100×50 (2×4) dressed framing lumber, walls and roof | |
3 pieces @ 2400 (96”) long | Roof ridge beam and 2 lower horizontal members |
4 pieces @ 1800 (72”) long | Top and bottom wall plates (front and rear walls) |
4 pieces @ 1620 (65”) long | Top and bottom wall plates (side walls) |
4 pieces @ 1620 (65”) long | Bottom horizontal member gable truss frame |
20 pieces @ 1160 (46 1/2”) long | Wall studs |
14 pieces @ 1160 (46 1/2”) long angled each and 30 degrees off square | Common rafters and fly rafters |
4 pieces @ 990 (39 1/2”) long angled each end as shown on plan | Raking frame members, gable truss |
2 pieces @ 612 (24 1/2”) long | Ridge beam support |
4 pieces @ 270 (11”) long angled back one end 30 degrees off square | Vertical members gable frame |
12 pieces @ approximately 255 (10 1/2”) long. Chek on-site | Blocking between the end rafters and the fly rafters |
10 pieces @ approximately 210 (8 1/4”) long, angled as shown on plan | Common rafter attachments |
300×25 (1×12) dressed lumber (suitable for exterior use) | |
2 pieces @ 1890 (75 1/2”) | Soffit board under gable overhang |
150×25 (1×6) dressed lumber (suitable for exterior use) | |
4 pieces @ approximately 1400 (56”) long angled each end as shown on plan | Barge board (gable rake board) |
2 pieces @ approximately 2400 (96”) long. Check on-site | Fascia board |
100×100 (4×4) dressed treated lumber | |
2 pieces @ 1800 (72”) long | Skids |
100×50 (2×4) dressed treated lumber | |
2 pieces @ 1800 (72”) long | Rim joists |
6 pieces @ approximately 1710 (69”) long. Check on-site | Floor joists |
Impressive complete playhouse plan for kids! My kids would love this one. Thank you!
Thanks for sharing this great information, would love to visit this site again.
Awesome article you shared.