Table of Contents
- 2The plans: Side and front elevation
- 3The Floor, Frame Cutting List and Instructions
- 4The base, the floor and the floor plan
- 5The wall frames and the stud layout plan
- 6The roof frame and roof detail plan
- 7The roof blocking, detail plan and legend
- 8 The covering, detail plan and cutting pattern
- 9The roof trim and the door
- 10The window and the handrail
- 11The materials list
The Floor, Frame Cutting List and Instructions
The Floor and Frame Cutting List.
Standard (ft and inch) version:
[a] 1 1/2″ x 5 1/2″: edge One of a series of parallel members used to support the floor. Part of the framing that provides the structure for a floor.; 2 @ 92″ long.
[b] 1 1/2″ x 5 1/2″: A standard or most commonly used horizontal framing member that supports the floor; 5 @ 73″ long.
[c] 3/4″ x 3 1/2″: decking boards; (random 175ft of).
[d] 1 1/2″ x 2 1/2″: The bottom horizontal framing member of the wall.; 2 @ 87″ and 2 @ 48″.
[e] 1 1/2″ x 2 1/2″: The top horizontal framing member of the wall.; 2 @ 87″ and 2 @ 48″.
[f] 1 1/2″ x 2 1/2″: A 100×50 (2×4) vertical framing member used to construct walls.; 18 @ 45″.
[g,h] 1 1/2″ x 2 1/2″: Blocks, see Block. and misc; (random 50ft of).
[i] 1 1/2″ x 2 1/2″: The horizontal line at the top of opposing sloping sides of a roof running parallel with the building length. A supporting member. support; 2 @ 19 1/4″.
[j] 1 1/2″ x 3 1/2″: ridge beam; 1 @ 92″.
[k] 1 1/2″ x 2 1/2″: A standard or most commonly used parallel member of a roof that supports the roofing boards. It slopes from the ridge to the top wall plate.; 10 @ 32 3/4″.
[l] 1 1/2″ x 2 1/2″: lean-to Structural member of a roof that supports the roof load and runs from the ridge to the top of the side walls.; 5 @ 36″.
[m] 1 1/2″ x 2 1/2″: lean-to rafter support; 5 @ 5 3/8″.
[n] 1 1/2″ x 2 1/2″: lean-to beam; 1 @ 92″.
[o] 1 1/2″ x 2 1/2″: see PILE; 3 @ 48″
Millimeter measurements. version:
[a] 145mm x 46mm: edge joist – 2 @ 2300mm long.
[b] 145mm x 46mm: common joist – 5 @ 1808mm long.
[c] 90mm x 32mm: decking boards – (random 53m of).
[d] 65mm x 46mm: bottom The top or bottom horizontal framing member of the wall. – 2 @ 2170mm and 2 @ 1200mm.
[e] 65mm x 46mm: top plate – 2 @ 2170mm and 2 @ 1200mm.
[f] 65mm x 46mm: stud – 18 @ 1108mm.
[g,h] 65mm x 46mm: blocking and misc – (random 15m of).
[i] 65mm x 46mm: ridge beam support – 2 @ 480mm.
[j] 90mm x 46mm: ridge beam – 1 @ 2300mm.
[k] 65mm x 46mm: common rafter – 10 @ 820mm.
[l] 65mm x 46mm: lean-to rafter – 5 @ 905mm.
[m] 65mm x 46mm: lean-to rafter support – 5 @ 135mm.
[n] 65mm x 46mm: lean-to beam – 1 @ 2300mm.
[o] 65mm x 46mm: post – 3 @ 1200mm
Step one: The pieces
Cut all the pieces to the lengths as given in the cutting list above.
The common rafters [k] have a 45° cut at each end.
The lean-to rafters [l] have a 10° cut at one end and a 55° (A line across the face of a piece of wood (at right angles to the length) is a square line. A line deviating from the square line is off square. Off-square refers to how many degrees the off square line is in relation to the square line. For example, a line at a 5 degrees angle to the square line, is 5 degrees off square.) cut at the other end.
The lean-to rafters supports [m] have a 10° cut at one end and a 45° cut at the other end.
All the other pieces are square cut.
Standard (ft and inch) version: