Table of Contents
- 1Introduction and quantities
- 2Quantities - continued
- 3Making the sledge
- 4The floor and Angle info
- 5Making the wall frames
- 6Cutting the wall panels
- 7Cutting the roof rafters
- 8Standing the walls / roof
- 9Fixing the roof boards
- 10Making the door / window
- 11Making the drip caps
- 12Sub-floor plan
- 13Floor plan
- 14Stud layout plan
- 15Front wall-frame plan
- 16Rear wall-frame plan
- 17Side wall-frame plan
- 18Front-wall siding plan
- 19Rear-wall siding plan
- 20Side elevation plan
- 21Roof plan
- 22Door and window plan
Quantities – continued
For the side walls (excluding curved braces) – 1 1/2″ x 3 1/2″ (90mm x 45mm) Timber, lumber. The hard fibrous lignified substance under the bark of trees.
Top/bottom plates, 4 pieces at 121 1/2″ (3036mm) long.
Studs, 10 pieces at 56 3/8″ (1410mm) long.
Blocks, see Block., 20ft (6m) in total.
For the curved bracing – 1 1/2″ x 9 1/2″ (240mm x 45mm) wood
8 pieces at 48″ (1200mm) long
For the roof frame
1″ x 10″ (250mm x 25mm) Uppermost horizontal framing member on a roof, to which the tops of the rafters are fixed., 1 piece at 141″ (3525mm) long.
1 1/2″ x 3 1/2″ (90mm x 45mm) rafters, 18 pieces at approximately 88″ (2200mm) long. Check on site.
Blocking, 54ft (16m) in total.
For the roof cover – 3/4″ x 6″ (150mm x 19mm) wood.
Boards used to cover the roof., Exterior visible flat trim board that follows the rake of the roof., A board covering the ends of the roof boards and sits flat over the barge board., and A horizontal framing member above the door/window opening., 54 pieces at 12ft (3600mm) long.
For the door and window
Cut out of leftovers.
3/4″ x 48″ x 96″ (19mm x 1200mm x 2400mm) A piece of wood made of three or more layers of wood veneer laminated together with glue., 11 sheets.
4″ x 4″ (100mm x 100mm) runners, 4 @ 120″ (3000mm).
3/4″ x 6″ (150mm x 19mm) roof cover, 54 @ 12ft (3600mm) or 650ft (195m) in total.
1 1/2″ x 3 1/2″ (90mm x 45mm) wall/roof framing, 465ft (140m).
1 1/2″ x 5 1/2″ (140mm x 45mm) floor frame, 127ft (38m).
1 1/2″ x 9 1/2″ (240mm x 45mm) curved bracing, 34ft (10m).
1″ x 10″ (250mm x 25mm) The horizontal line at the top of opposing sloping sides of a roof running parallel with the building length. A piece of sawn, or dressed lumber of greater width than thickness. Usually 19mm (3/4") to 38mm (1 1/2") thick and 75mm (3") or more wide., 1 @ 141″ (3525mm).
Acrylic Any broad, thin surface.,
4 @ 195mm x 345mm.
2 @ 250mm x 445mm.
And you will need an assortment of nails and screws and hardware of choice, plus some felt A building paper that covers roof frame prior to the cladding being fixed. Reduces air movement and helps avoid the risk of water ingress. (or similar A building paper that envelops the exterior walls or roof frame prior to the cladding being fixed. Reduces air movement and helps avoid the risk of water ingress.)