Go to Buildeazy Home Page color break
   
Home   
Contents   
spacer
Custom Search
 
Garden Shed Project
a tudor style garden shed
woodworking projects from the do-it-yourself carpentery workshop




How to build an
8x7 Tudor-Style Garden Shed
See the video
PAGE CONTENTS BELOW USER COMMENTS/PHOTOS
Page 14: Covering the roof
Section 14.1 Laying and fixing the roof boards

The rafters have already been marked at every 4" (100mm) along the top for roof board placement. That was done in section 8.1.

putting the roof cover on the shed Now clamp a board to the outside of a fly-rafter, running all the way up. Make the board at least the length of the rafter and protruding (sticking up) an inch or two above the fly rafter, creating a straight-edge to butt the ends of the roof boards up to.

Begin laying and fixing the roof boards from the bottom and work your way up.

Hold the first board with one end against the straight-edge and the top edge flush with the first row of marks on the rafters, which are 4" (100mm) up from the ends.

Nail the first board to the rafters using one 3" (75mm) flathead galvanized nail at each rafter.
For the first board only, nail it 3" (75mm) down from the top of the board.

Note: Use 3" (75mm) flathead galvanized nail if the boards you are using are 3/4" (19mm) thick. If you use thicker boards, say 1" (25mm) thick, then use 3 1/2" (90mm) nails.

Next the second board.

Hold the second board with one end against the straight-edge, and the top edge flush with the second row of marks.
The bottom of the second board should be overlapping the top of the first board by 2" (50mm).

Nail the board to the rafter using one 3" (75mm) flathead galvanized nail 4 1/2" (112mm) down from the top of the board at each rafter.
The nail should go through both boards, the bottom of the top board and the top of the lower board.

Likewise with the rest of the roof-boards working your way to the top.

Section 14.2 Fixing the ridge cap

Fix a length of galvanized 2" x 2" (50mm x 50mm) angle flashing (ridge capping) along the top of the apex over the roof boards. shed ridge capping

Nail through the side of the flashing, through the roof boards into the top of the rafters.

A Tip or Two!
There are 12 plan drawings you can refer to at anytime.
To see them go to page 2.
The page contents are listed at the bottom of every page but the Main Index page also lists every sub-section.

Section 14.3 About the barge cap and barge board the shed barge cap and barge board

The barge cap and the barge board is the trim that runs up the gable to cover the ends of the roof boards and the fly rafters.

The barge caps sit flat on top of the roof boards, and overhangs the edge of the fly rafters by 2" (50mm).

The barge boards are fixed to the fly rafters directly under the barge caps.

The barge cap is 3/4" x 6" (150mm x 19mm) board and the barge board is 3/4" x 3" (75mm x 19mm) board.

Note: Use spare roof boards for the barge cap and rip (cut down lengthwise) in half some roof boards to make up the barge boards.

Section 14.4 Cutting and fixing the barge cap and the barge board

The barge capping is a piece of 3/4" x 6" (150mm x 19mm) board that runs up the rake of the roof, sitting flat over the ends of the roof boards.

Cut four lengths of 3/4" x 6" (150mm x 19mm) at 76 3/8" (1910mm) long, with the bottom cut square and the top cut with the circular saw blade set at a 36.87 degree angle off square.

Need help working out the angles?   See Getting the angles
Fix the barge cap in place with one edge overhanging the fly rafter by 2" (50mm).

The barge board is a piece of 3/4" x 3" (75mm x 19mm) board that goes under the barge cap and covers the fly rafter.

Cut four lengths of 3/4" x 3" (75mm x 19mm) at 75 1/4" (1880mm) long, with the bottom cut rounded and the top cut angled in 36.87 degrees off square.

Fix them to the fly rafters directly underneath the barge capping.

Note: Rip some roof boards in half (cut down lengthwise) to make the barge boards.

<<< Previous page  |  Main Index  |  Next page >>>
PAGE CONTENTS
bullet Page 1: Introduction, Informative Stuff
bullet Page 2: Plan Drawings and Material List
bullet Page 3: Making the floor
bullet Page 4: Making the front and rear wall frames
bullet Page 5: Making the curved bracing members
bullet Page 6: Making the side wall frames
bullet Page 7: Making the plywood wall panels
bullet Page 8: Cutting and preparing the roof frame
bullet Page 9: Painting the wall frames and panels
bullet Page 10: Fixing the wall panels to the frames
bullet Page 11: Positioning the floor
PAGE CONTENTS
bullet Page 12: Standing the walls
bullet Page 13: Assembling the roof frame
bullet Page 14: Fixing the roof cover
bullet Page 15: Making the door
bullet Page 16: Making the window
bullet Page 17: Hanging the door and window
bullet Page 18: Fitting the drip caps
bullet Page 19: Help
bullet Page 20: Glossary
bullet Page 21: User Comments/Photos
bullet Page 22: Main Index


   

Copyright © Buildeazy.Com Ltd. All rights reserved. Reproduction of any material
in this website is strictly prohibited without expressed written permission from the owner.

Custom Search